Instant locking, lowers installation torque, limited reusability. Homepagedin standards din 26726 technical delivery conditions for fasteners part 26. The din male 24 internal cone seat will seal with flareless female swivel fittings. This specification lists the japanese standard jis, jpi,british standard bs, and deutshe industrie normen din substitutes for astm specifications relating to materials for plates, pipes, tubes, forging, castings, bolts and nuts, bars and shapes, piping fittings, and nonferrous materials, in general use. Thread specification metric din din 38521 technical data 10. Steel screws, bolts and studs with locking coating. Iis manufactures belleville washer in imperial as well as metric sizes. Homepage din standards din 26728 fasteners part 28.
Din 267 part 5 shall apply with regard to acceptance testing. The german standard din 267 part 11 on corrosionresistant stainless steel fasteners has been withdrawn due to the mandatory implementation of the european enproductstandards of hexagon bolts, screws and nuts. Plain plain din 2672 applies with regard to surface roughness. A file purchased with a singleuser licence can be saved and viewed only on one personal computer and can be printed only twice. Din26728 pdf asme bpvc 20 set,ul pdf download,csa pdf.
Steel screws, bolts and studs with locking coating, technical specifications. Steel screws, bolts and studs with adhesive coating, technical specifications. These produce a 90% utilization of the bolt yield strength. Homepage din standards din 267 28 fasteners part 28. Fasteners, technical delivery conditions, design fontsize. Technical delivery conditions acceptance inspection this document comes with our free notification service, good for the life of the document.
Thread locking is an integrated part of the fastener. Iis belleville washers are designed specifically for heavy duty bolted section such as bus bars, transformers, rectifiers, heat exchangers, transmission etc. Iso 6g klasse aus din 26727 aus din 26727 m lb m a quelle. Download the din en iso technical information brochure here. This data chart is also available for downloading as a viewableprintable acrobat pdf file. Vasile bianu insemnari din rasboiul romaniei volumul file. Substitute material jis, bs, din for astm specification contents section 1. Din2672 pdf asme bpvc 20 set,ul pdf download,csa pdf.
This standard specifies technical specifications for steel screws, bolts and studs with jamming coatings. Din 267 200705 fasteners technical specifications part. Ksjis symbol ksjis number remark din type din material remark number number a179 seamless cold drawn lowc k01200 stbh340stb35 d3563g3461 st 35. Conical spring washers for boltnut assemblies sponsored link immediate download released. This file contains additional information such as exif metadata which may have been added by the digital camera, scanner, or software program used to create or digitize it.
Product sheet product sheet rohs weee compliance statement safety msds. Din 267 part 9 shall apply with regard to electroplating. Din 267 part 4 mechanical properties of steel din nuts. These enproductstandards are indentical with existing international isostandards, which refer to. Din en iso 10683 applies with regard to zinc flake coatings. Plain plain din 267 2 applies with regard to surface roughness. Din 933 1987 this standard contains specifications for fully threaded hexagon head screws with coarse metric thread for diameters m 1. Din2675 pdf asme bpvc 20 set,ul pdf download,csa pdf. Steel screws, bolts and studs with locking coating technical delivery conditions sponsored link immediate download released.
Din en iso 4042 applies with regard to electroplating. Adhesivecoated steel screws, bolts and studs foreign standard the document specifies technical specifications for steel screws, bolts and studs with jamming coatings. Vdi 2230 pdf english free 24l as legislativas 2015. The calculations are based on a friction coefficient of 0. Din 267 part 20 shall apply with regard to permissible surface discontinuities. Herstellerangaben din 267 teil 27 anderungen vorbehalten. To avoid such failure bollhoff offers a wide range of chemical thread retention solutions, which are. Din 267 part 10 table 2, limit dimensions for bolt threads prior to hotdip galvanizing calculated on the basis of the screw thread tolerance. Fasteners with locking coating wurth industrie service. The tests are conducted using test nuts or components provided by the customer. May 15, 2018 this data chart is also available for downloading as a viewableprintable acrobat pdf file. Experiential values are available for adjusting screws.
Din standards are the results of work at national, european andor international level. Din 267 part 20 shall apply with regard to permissable surface discontinuities. Once accepted, the standards project is carried out according to set rules of procedure by the relevant din standards committee, the relevant technical committee of the european standards organization cen cenelec for electrotechnical standards or the. Assemblyactuated, fastcuring and vibrationresistant. Din 267 part 4 for type m and type v fine thread nuts.
Belleville washer, belleville washers, manufacturers. This is an incomplete list of din standards the status column gives the latest known status of the standard. Din has used nylok fasteners on their products for years. Homepage din standards din 267 26 technical delivery conditions for fasteners part 26. If the file has been modified from its original state, some details such as the timestamp may not fully reflect those of the original file. Din 267 part 2 shall apply with regard to surface roughness. Nylok has been a leading supplier of fasteners in the industry since 1942. If a standard has been withdrawn and no replacement specification is listed, either the specification was withdrawn without replacement or a replacement specification could not be identified.